A pattern grid and sound editor for the Roland AIRA Compact S-1. It runs in your browser, sends MIDI to the S-1 and doesn't change its firmware. Your patterns stay on this computer. It needs a current Chrome or Edge on a computer. It's unofficial and not affiliated with Roland.
Visits to this page are counted anonymously with GoatCounter, which uses no cookies. It never receives your patterns or patches.
Set up
- Connect the S-1 to your computer with a USB-C data cable, and turn it on.
- Allow MIDI access when asked. The MIDI badge turns green when the S-1 is found. If it says MIDI blocked, click the icon to the left of the address, set MIDI devices to Allow, then click Allow MIDI.
- Click a note name in the grid. You should hear it on the S-1.
- Check that Channel at the bottom matches the S-1's MIDI channel. It's 3 unless you've changed it.
Working in a key
- Choose a Key and Scale. The grid only shows notes in that key, so anything you draw fits. The key's root note is highlighted. Off, first under Key or Scale, turns the key off: the grid shows every note, and nothing is marked as in or out of a key. Notes stay where they are when you turn it off. Choosing a key again, with Move notes with key on, moves each note to the nearest one in that key and scale, without changing the root. With it off, chords are built from semitones, and Generate needs a key. Imported MIDI files and loaded patches come in with the key off, so every note shows as written, and the status line suggests the key they sound in. Choose a key and scale afterwards to fit them to it.
- Move notes with key moves all of your patterns into a new key when you change it, keeping each note's place in the scale. Turn it off to leave notes where they are.
- All notes shows every note. Notes outside the key are marked in their row name.
- Draw places a single note, a power chord, a triad or a 7th, using notes from the key. To hear chords, set Polyphony to Poly on the VOICE tab.
- Idea and Generate write a bassline, melody, arpeggio or chord pattern in the key. Generating replaces the current pattern, and Undo brings it back.
- Choosing an Idea also sets every sound control to a good starting point for it, such as a round, punchy tone for a bassline. Init does the same for the idea already chosen. Hear original, under the sound controls, brings back the sound you had. Generating doesn't change the sound, so you can try more patterns without losing your tweaks.
- Sine sets every control to get as close to a sine wave as the S-1 can. It has no sine oscillator, so this is a square wave through the low-pass filter, with full key follow. Lower Cutoff for a purer but quieter tone, or raise it if notes get thin. Very high and very low notes may need different settings.
- Shift moves the whole pattern a step earlier or later, wrapping around. Scale moves every note a step through the scale, and Oct moves them an octave.
- Click or drag along the step numbers above the grid to choose steps. Copy (or Cmd+C) copies their notes. Choose where they go, in this pattern or another, then Paste (or Cmd+V), which replaces what's there. Click a chosen step again or press Esc to clear.
- Velocity and Set change every note in the chosen steps, or the whole pattern if none are chosen.
Mouse and keyboard
| Click a step | Add or remove it, as long as you don't drag. New steps use the Length setting, or one step when it's Off. |
| Drag from an empty step | Draw one note as long as you drag. It snaps to the grid, or hold Alt for single ticks. |
| Drag a note | Change where it ends, longer or shorter, from anywhere on its first step or its end marker. It moves in eighths of a step, or hold Alt for single ticks. |
| Cmd-drag across steps | Fill separate steps. Dragging from a filled step removes steps instead. |
Right-click a step or Control-click on a Mac | Edit velocity, length, timing and probability. |
| Shift-click a step | Cycle velocity: full, 70%, 40%. |
| Click a note name | Hear that note on the S-1. |
| Space | Play and stop, unless you're typing in a text box such as a name or the chain. |
| T | Turn triplets on or off. |
| Cmd or Ctrl + Z | Undo. |
| ? and Esc | Open this help, and close it or the step editor. |
Sub-steps, chains and recording
- Sub-step, when you right-click a step, plays it in quick repeats using the S-1's 14 patterns, where o plays and - is silent. They play here, save to the S-1, and show on the note.
- Chain takes pattern numbers such as 1 1 2 3. Tick On and Play goes through them in order, looping. Clicking a pattern during playback plays it next, then the chain carries on.
- Rec records notes from the input and channel chosen beside it: the S-1's keys, another keyboard, or any input on any channel. While playing, notes land on the nearest step and last as long as you hold them, or the length chosen in Length if it isn't Off, and each time round the loop adds to what's there. While stopped, each key adds a note and moves on a step, starting from the chosen step. Undo takes back the whole take.
- Click plays a metronome click on each beat while the pattern plays, louder on the first beat of each bar. It comes from this computer's speakers, not the instrument, and stays on or off for next time.
- While recording, notes from another keyboard are passed on to the S-1, so you hear them. If MIDI Hub is also routing that keyboard to the S-1, you'll hear each note twice, so choose one.
Drawing knob movements
- Knobs opens a lane under the grid. Choose a knob and drag to draw how it moves through the pattern, or Alt-drag to erase. The S-1 stores 8 points per step and up to 8 knobs per pattern.
- They play from this page and save to the S-1 as motions, as well as to the library. Shift moves them along with the notes.
- Copy all to copies every knob's movements in this pattern, including a loaded patch's, to another pattern, replacing any it has. The notes aren't copied, and Undo takes it back. Movements past the end of a shorter pattern are left out.
- A loaded patch's motions show here too. Drawing replaces its recorded motions with what's shown when you save, and keeps any pitch bend movements.
Sound controls
- Back to saved sound returns every setting to what's saved in the pattern's patch, after trying changes. Hear original brings back the sound you had. Light mode at the top switches the page's colours, and it's remembered.
- Vary nudges the sound's levels a little or a lot, leaving tuning, pan and switches alone. Hear original flips between the sound before you started and the new one.
- The panel on the right has every control the S-1 accepts over MIDI, grouped into tabs. Changes are immediate, even during playback.
- The sound stays the same when you switch patterns. Only loading a patch or a saved sound changes it, and saving a pattern saves the sound as it is then.
- Turning a knob on the S-1 updates the matching control here. A value shown as ? hasn't been set or received yet, because the S-1 can't report its settings when asked. Init or loading a patch fills them in.
- Save to library, below the controls, saves the current pattern and sound together as a patch in your library folder. Values shown as ? keep the value from the patch you loaded, or otherwise the blank patch's.
- The drawn wave's shape, and settings with no MIDI control, can only be changed on the S-1.
- Follow S-1 shows the sound of whichever pattern you choose on the S-1. The S-1 can't send its settings, so the page reads them from a copy of its BACKUP folder: click S-1 backup and choose the S-1 drive or a saved copy. Opening the S-1 drive for Import from S-1 or Save to S-1 updates the copy too. Nothing is sent back to the S-1, and the grid doesn't change.
- The copy is only as new as the last backup. Edits made on the S-1 since then show once you move those knobs, so take a new backup after writing patterns on the S-1.
Patch library
- The LIBRARY tab keeps patches as files in a folder you choose on this computer. Each holds a full S-1 pattern: notes, motions, and every sound setting.
- Hear plays a patch at its own tempo with its own sound, without changing the grid. Your sound comes back when it stops, apart from any controls showing ?, as the page doesn't know what they were.
- ☆ marks a favourite, and Favourites only shows just those. Tags adds words that the search also finds. Both are saved in a library-info.json file in your library folder.
- Import from S-1 lets you pick which of the S-1's 64 patterns to copy into the library, and name each one. It reads the S-1's USB drive, or a BACKUP folder you saved, and doesn't change anything on the S-1.
- Import backup fills it from an S-1 BACKUP folder, with its patterns that have notes and one blank patch. These are whatever is saved on your S-1, which may include your own edits.
- Click a patch to load it: the grid fills with its notes, its sound controls update, and its sound is sent to the S-1. The play button also starts playback. A patch's key is estimated from its notes.
- Save to library saves the current pattern and sound as a patch, and works with no notes if you just want to keep a sound. Loading a patch fills in its name, so saving updates it after asking. Type a new name to keep both.
- Names are entirely up to you: use Name to rename a patch. The S-1 doesn't store names, and its files have fixed names by slot, which the page handles when saving.
- To send several at once: tick patches in the list, then click Send to S-1. Each patch gets a row with its own slot. They start on the next empty slots. To change one, select its row and click a slot, or use its list. The same patch can go to several slots with Add to list.
- To S-1 on a single patch opens Save to S-1 with that patch selected.
- When saving, hovering over a slot shows which library patch it holds, if its contents exactly match one.
- Delay sync on the FX tab has no MIDI control, so it takes effect once a pattern is saved to the S-1. Loading a patch fills it in. With sync off, Delay time shows ms. With sync on, it shows a note value, one of 16 from 1/128 to 1/4, as the S-1's knob sends in that mode. Either one is what's saved. If the slider doesn't match the knob, set Delay sync to match the S-1.
- Some settings have no MIDI control, like delay feedback or a drawn wave, so they won't be heard during live playback. They're kept in the file and work once a patch is on the S-1. Motions and sub-steps play live here too, as a close match.
Patterns and the S-1's own memory
- Patterns 1-16 here are stored in this browser, and clearing its data for the site erases them. Back up saves all 16, their patches and the sound to one file, and Restore loads it back. Export MIDI keeps one pattern's notes as a file, with sub-steps written as separate notes.
- Import MIDI replaces the current pattern with the notes from a MIDI file, and Undo brings it back. All its tracks are merged, leaving out drums on channel 10 if there's anything else. It also sets the tempo and estimates the key. The pattern gets 1, 2, 4 or 8 bars, whichever fits, and anything past 8 bars is cut. A patch loaded into that pattern no longer applies, though the sound stays.
- Patterns play from this page, so the page must stay open.
- Save to S-1 writes a pattern and sound into the S-1's memory, using its USB backup and restore. It takes a restart of the S-1, and the button walks you through it. This isn't a method Roland documents, so keep a copy of the S-1's BACKUP folder.
- A save holds up to 64 steps, 4 notes per step and values on 1/16 steps. Anything else is rounded or left out, and you're told first. Long notes are saved as tied steps. Settings shown as ? stay as they are in the pattern's source. Pan and mod wheel aren't stored in patterns. A pattern loaded from the library keeps its motions, and drawn knob movements are saved. Other saves remove any motions in the slot being replaced. Library patches sent directly are copied exactly.
- Record to S-1 plays a pattern once for the S-1 to record instead: select a pattern on the S-1, press REC, then PLAY, then click the button soon after. Timing depends on how it records, and this hasn't been confirmed on the hardware.
- Sync plays this page together with MPC Grid when both are open in the same browser, each with its MIDI connected. Pressing Play or Stop on either one starts or stops both, from the start of their patterns, at the tempo of the page you pressed. Changing the BPM on either changes both. Patterns of different lengths each loop in their own time. Untick it on either page to play them separately. The badge beside it shows whether the other page is connected.
- Send clock starts the S-1's own sequencer as well, so you may hear both unless its pattern is empty.
If you hear nothing
- Check that the MIDI badge is green, and reload the page if the S-1 was off when it opened.
- Check the channel, and that the S-1's volume and filter Cutoff are up. Filter cutoff at minimum gives no sound.
- Use Panic if a note gets stuck.